欧美激情视频网址I狠狠色依依成人婷婷九月I久久综合站Iav青草I日本黄色xxxxI丰满放荡岳乱妇91wwI日韩激情中文字幕I国产精品,I成人高清I20日本xxxxxxxxx46I国产精品9191I日韩熟妻I91精品人妻一区二区三区蜜桃2I国产黄色一级片I欧美色涩I69福利视频Ihd国产人妖ts另类视频I亚色网站I青青草手机在线视频I国产精品手机在线Iwww.色午夜.comI亚洲国产精品久久久久制服I色射网I寡妇avI亚洲激情图

According to the actual situation on site, fine tune the various partitions of the window line to ensure aesthetics and consistency. The thickness of the thick plaster layer (starting from the upper surface of the board groove) should not exceed 30mm. The EPS board is filled with anti cracking mortar, and the gypsum layer is completely covered with steel mesh and board anchors, with anti cracking measures taken. The thick plaster layer should be applied several times and maintained under alternating dry and wet conditions. When it is necessary to reserve construction joints for crack resistant mortar, a stepped ramp should be used. Spray inside the corners and spray from the inner corners to both sides to reduce the accumulation of inner corners. After 15-20 minutes, gently press the burr formed on the inner corner with an iron plate to keep the inner corner straight. The details refer to the starting point of the spray.

1. Brush the horizontal line of the paintball shooting, then paste a 2cm wide beautification paper, and then spray real stone paint to remove the beautification paper.

2. Control point: When repairing, please ensure that the joint of the partition is on a horizontal surface and does not exceed the upper and lower horizontal lines.

The concrete for the wall should be poured in layers, with layer by layer pouring and layer by layer vibration, and the layer height should be controlled within 500mm. It is strictly prohibited to cut open the EPS board with the pump tube, and the vibrating rod must not come into contact with the EPS board. After removing the liner, twist the holes with dry cement mortar, seal the EPS board holes with similar materials, and the hole length should not be less than 50mm. For local unevenness on the surface of EPS boards, EPS granular insulation paste should be used for repair and leveling. The thickness of the repaired tablet should not exceed 10mm.

When pasting the insulation board, first apply a layer of glue on the insulation board. Then stick a layer of insulation adhesive board on the wall, press it evenly, and use a 2000mm ruler to check the flatness and verticality of the insulation board. Insulation boards should not collide with each other, and the upper and lower boards should be bonded together. At the corners of the wall, the insulation boards should be connected together; At the entrance and exit of doors and windows, the distance between the connection of the insulation board and the parallel edge of the doors and windows should be greater than 200 millimeters.

Non flammable, fire-resistant characteristics: high temperature calcination above 1200 ° C, combustion performance A1. The refractory bricks and refractory materials of thermal power plants are ideal materials for external insulation systems and fire barriers with fire prevention requirements. The insulation board has the characteristics of fire resistance, flame retardancy, small deformation coefficient, aging resistance, stable performance, environmental protection, good compatibility with wall base and plaster layer, safety and stability, and the same service life as buildings. The specifications used are generally 123mm × 600mm × 90mm; The commonly used specifications for rock wool board are 600mm × 600mm × 130mm. There shall be no less than 6 anchorages per square meter, usually 1 per corner and 2 in the middle. For panels less than 4 millimeters wide, an anchor point should be provided at each corner; For wide panels ranging from 400mm to 800mm, an anchor point should be placed at each corner and a middle anchor point.